JVC RX-F31S Instruction Manual

Adjusting the subwoofer audio position, Activating TV Direct

Adjusting the subwoofer audio position, Activating TV Direct

14
Adjusting the subwoofer audio
position
If the subwoofer sound is much reinforced for stereo sound
compared to the sound reproduced with multi-channel, set the
subwoofer audio position. The subwoofer output level is
automatically decreased by the selected value when you are
listening in stereo.
The AUDIO P. indicator lights up when this function is activated.
• Once you have made an adjustment, it is memorized for each
source.
From the remote control ONLY:
Press SOUND, then press A.POSITION repeatedly.
• Each time you press A.POSITION, the subwoofer audio position
level changes as follows:
AUDIO P. indicator
The smaller the number becomes, the more the level decreases
automatically when listening in stereo.
• If no adjustment is required, select “OFF” (initial setting).
NOTES
• The minimum subwoofer output level is –10 dB.
Ex.: When setting the subwoofer output level to “–8 (dB)” and
the subwoofer audio position to “–4 (dB),” the subwoofer
output level when listening in stereo will be –10 dB.
To adjust the subwoofer output level, see page 29.
• This function is not available when the Surround/DSP mode is
activated or “DVD MULTI” is selected.
• After pressing SOUND, the numeric buttons work for sound
adjustments. To use the numeric buttons to operate your target
source, press the corresponding source selecting button before
operation; otherwise, the remote control may not work as you
intend.
Activating TV Direct
TV Direct enables you to use this receiver as an AV selector
while the receiver is turned off.
When TV Direct is activated, the pictures and sounds go from the
video components such as DVD player to the TV through this
receiver. Thus, you can use the video components and the TV as
if they were connected directly.
• This function takes effect for the following sources—DVR/DVD,
VCR, and DBS.
To activate (or deactivate) TV Direct, follow the procedure below:
1
Press TV  DIRECT.
All the indications disappear, then the source lamp of the
current source lights in green.
2
Turn on the video component and TV.
3
Select the target video component.
On the front panel:
Turn SOURCE SELECTOR until one of the
source lamps—DVR/DVD, VCR, or DBS—lights
in green.
From the remote control:
Press one of the source selecting buttons—
DVR/DVD, VCR, or DBS.
The source lamp corresponding to the selected source lights
in green.
To cancel TV Direct and turn off the receiver, press
 STANDBY/ON on the front panel (or 
 AUDIO on the remote
control).
The receiver is turned off and the standby lamp lights up.
To cancel TV Direct and turn on the receiver, press TV DIRECT
again.
The receiver is turned on and the source lamp currently selected
lights in red.
NOTES
• When TV Direct is activated, you cannot enjoy any of the sound
effects the receiver produces, and cannot use the speakers
connected to the receiver.
• When TV Direct is activated while “DVD MULTI,” “FM,” or “AM” is
selected as the source, the source changes to the last selected
source—“DVR/DVD,” “VCR,” or “DBS.”
When operating the receiver
using the remote control, set
the mode selector to
“AUDIO/TV/VCR/DBS.”
EQ
LPCM
L
LS SB RS
S . WFR
PL
NEO : 6
DSP 3D
LFE
C
R
DOLBY D
DTS AAC
96 / 24
AUTO SR
C.TONE VIRTUAL SB
AUDIO P.
BASS
TA NEWS INFO RDS TUNED ST
SLEEP
AUTO MUTING
AUTO MODE
ATT
HP
MHz
kHz
–2
–4
–6
OFF (canceled)
EN12-15RXF31S[A]1.p65
05.6.13, 10:36
14