JVC RX-F31S Instruction Manual

Basic operations

Basic operations

12
Basic operations
2
 Select the source to play
On the front panel:
Turn SOURCE SELECTOR until the source name
you want appears on the display.
The source lamp corresponding to the selected source lights in
red.
• As you turn SOURCE SELECTOR, the source changes as
follows:
DVD MULTI:
Select for the DVD player using the analog
discrete output mode (5.1-channel
reproduction).
DVR/DVD (DGT)
*
: Select for the DVD recorder or DVD player.
VCR (DIGITAL)
*
:
Select for the VCR.
DBS (DIGITAL)
*
:
Select for the DBS tuner.
TV (DIGITAL)
*
:
Select for the TV.
FM:
Select for an FM broadcast.
AM:
Select for an AM broadcast.
From the remote control:
Press one of the source selecting buttons.
• For the tuner, press FM/AM. Each time you press FM/AM, the
band alternates between “FM” and “AM.”
* Selecting the analog or digital input mode
For a component you have connected using both the analog
connection and the digital connection methods (see pages 7 to 11),
you need to select the correct input mode.
• You can select the digital input only for sources which you have
selected digital input terminals for. (See “Setting the digital input
(DIGITAL IN) terminals—DIGITAL IN 1/2/3” on page 24.)
From the remote control ONLY:
Press ANALOG/DIGITAL INPUT to select the
analog or digital input mode.
• Each time you press the button, the input mode alternates
between the analog input (“ANALOG”) and the digital input
(“DGTL AUTO”).
This setting is memorized for each source.
DGTL AUTO:
Select for the digital input mode. The receiver
automatically detects the incoming signal
format, then the digital signal format indicator
(LPCM, DOLBY D, DTS, or DTS 96/24) for
the detected signal lights up.
ANALOG:
Select for the analog input mode.
Initial setting: DGTL AUTO
NOTE
When you select “DVD MULTI,” “FM,” or “AM” as the source, the
analog and digital input mode is not available.
1
 Turn on the power
Press 
 STANDBY/ON (or 
 AUDIO on the
remote control).
The standby lamp goes off and the source lamp of the current
source lights in red.
Current source name appears.
To turn off the power (into standby)
Press 
 STANDBY/ON (or 
 AUDIO on the remote control)
again.
The standby lamp lights in red.
NOTE
A small amount of power is consumed in standby mode. To turn
the power off completely, unplug the AC power cord.
When operating the receiver
using the remote control, set
the mode selector to
“AUDIO/TV/VCR/DBS.”
 Source lamps
The on-screen display appears on the TV screen for 5 seconds
(except “turning off the sounds temporarily”) to show the
indication in the following cases:
– When you select the source (see right column).
– When you adjust the volume (see page 13).
– When you turn off the sounds temporarily (see page 15).
– When you select the Surround/DSP modes (see page 39).
To cancel the function, set “SUPERIMPOSE” to “SUPERIMPOSE:
OFF” (see page 25).
1
2
3
EQ
LPCM
L
LS SB RS
S . WFR
PL
NEO : 6
DSP 3D
LFE
C
R
DOLBY D
DTS AAC
96 / 24
AUTO SR
C.TONE VIRTUAL SB AUDIO P. BASS
TA NEWS INFO RDS
TUNED ST
SLEEP
AUTO MUTING
AUTO MODE
ATT
HP
MHz
kHz
EQ
LPCM
L
LS SB RS
S . WFR
PL
NEO : 6
DSP 3D
LFE
C
R
DOLBY D
DTS AAC
96 / 24
AUTO SR
C.TONE VIRTUAL SB AUDIO P. BASS
TA NEWS INFO RDS
TUNED ST
SLEEP
AUTO MUTING
AUTO MODE
ATT
HP
MHz
kHz
DVR/DVD (DGT)
DVD MULTI
VCR (DIGITAL)
DBS (DIGITAL)
TV (DIGITAL)
FM
AM
(Back to the beginning)
1
3
2
EN12-15RXF31S[UJ]2.p65
05.5.13, 16:57
12