Yamaha RX-V2400 Owner Manual

Programming codes from other remote controls

Programming codes from other remote controls

61
English
REMOTE CONTROL FEATURES
A
D
V
ANCED 
OPERA
T
ION
5
Press LEARN again to exit from the setup 
mode.
• The supplied remote control does not contain all possible 
manufacturer codes for commercially available AV components 
(including Yamaha AV components). If operation is not 
possible with any of the manufacturer codes, program the new 
remote control function with the Learn feature (see below) or 
use the remote control supplied with the component.
• If you have already programmed a remote control function for a 
button, the function by learning programming takes priority 
over the setup manufacturer code’s function.
• “ERROR” appears in the display window when press any 
buttons other than indicated in each step, or when you press 
more than one button at once.
If you want to program functions not included in the basic 
operations covered by the manufacturer code, or an 
appropriate manufacturer code is not available, do the 
following. You can program any of the buttons available in 
the component control area (see page 59). The buttons can 
be programmed independently for each component.
This remote control transmits infrared rays. If the other remote 
control also uses infrared rays, this remote control can learn most 
of its functions. However, you may not be able to program some 
special signals or extremely long transmissions. (Refer to the 
operation instructions for the other remote control.)
1
Set 10KEY/DSP to 10KEY.
y
It is also possible to program in this unit’s control area with 
10KEY/DSP set to DSP. However, if you do this, you will 
not be able to control this unit and select sound field 
programs.
2
Press an input selector button to select a 
source component.
3
Place this remote control about 5 to 10 cm 
apart from the other remote control on a flat 
surface so that their infrared transmitters are 
aimed at each other.
4
Press LEARN using a ballpoint pen or similar 
object.
Do not press and hold LEARN. If you hold it down 
for more than three seconds, the remote enters the 
manufacturer code setting mode.
y
Complete each of the following steps in 30 seconds. 
Otherwise, the learning mode will be automatically 
canceled. In this case, press LEARN again.
5
Press the button at which you want to 
program the new function.
“LEARN” is displayed.
Notes
Programming codes from other 
remote controls
Note
LEARN
DSP
10KEY
PHONO
CD
DVD
DVR/VCR2
VCR 1
DTV
CBL/SAT
CD-R
MD/TAPE
TUNER
V-AUX
TRANSMIT
RE-NAME
ST
ANDBY
INPUT MODE
SYSTEM
CLEAR
L
EARN
MA
CR
O
OFF
ON
MA
CR
O
PHONO
MUL
T
I CH IN
CD
DV
D
D
VR/VCR2
VCR 1
TITLE
SOURCE
ENTER
DTV
CBL/SA
T
CD-R
MD/T
APE
TUNER
V-
A
U
X
PO
WER
PO
WER
5 to 10 cm (2 to 4 inch)
Flashes alternately
LEARN
TRANSMIT
RE-NAME
ST
ANDBY
INPUT MODE
SYSTEM
CLEAR
LEARN
MA
CR
O
OFF
ON
MA
CR
O
PHONO
MUL
TI CH IN
CD
DV
D
D
VR/VCR2
VCR 1
TITLE
SOURCE
ENTER
DTV
CBL/SA
T
CD-R
MD/T
APE
TUNER
V-
A
U
X
PO
WER
PO
WER
00_RX-V2400U_EN.book  Page 61  Friday, October 10, 2003  10:54 AM